Buy Yamaha Outboard Parts

Announcement

Collapse
No announcement yet.

throttle friction, 704 standard flush mount

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    throttle friction, 704 standard flush mount

    I have a 2003 flush mount throttle for a 150 2 stroke, the type that only the handle is visible and the box is in the gunnel. I need to know how to tighten the throttle. the screws that I found appear to be stop adjustments not friction adjusters. the box is mounted horizontally.
    Last edited by tomcosta; 10-23-2014, 08:22 AM.
    Tags: None
  • #2
    remove the 4 black screws, remove black cover, adjuster is on backside of control

    Comment

    • #3
      there is a large black plastic cover and a small one, which one do I need to remove? I will be reaching blind into the gunnel and would like to get it right the first time

      Comment

      • #4
        in the Yamaha exploded diagram of the flush mount control, can you identify which item number is the correct screw?
        thank you

        Comment

        • #5
          its outside,exposed,single slotted pin

          Comment

          • #6

            Are you sure we're talking about the same unit? My control mounts to the side wall, only the lever is exposed, I have attached some images and the Yamaha diagram. the guts are behind the wall, there are no black screws, and the only screws on the outside are the throttle stop adjusters. there are two black plastic covers on the backside of the unit, top right of the diagram, I assume the friction adjuster is under one of them but I don't know where. I have run my fingers all around the perimeter of the box, but the only screws I find are the stop screws.
            thanks for your attention on this
            Last edited by tomcosta; 10-22-2014, 02:29 PM. Reason: add images

            Comment

            • #7
              oh you said 704
              is it a 6x3? as used in mastercrafts? side mount, round knob handle ?

              these are 704's

              https://www.google.com/search?q=yama...w=1366&bih=670
              Last edited by jb123; 10-22-2014, 02:11 PM.

              Comment

              • #8
                He said 704 but a 704 is a top mount box. Not a side flush mount.

                Comment

                • #9
                  I didn't say 704, it is a flush mount like in the pictures in the previous post. I can't find any identifying info on it, it just says "Yamaha Remote Control" on the handle. I did find some pictures that show a manual with the unit. It appears that 6X3 is the current version and that I might have a 6X0, but I can't find any information on either of these. It's on a Wellcraft.

                  Comment

                  • #10
                    throttle friction, 2003 flush mount remote control

                    sorry, I just realized the title of the post says 704, not sure why. I changed it, thanks for pointing that out.

                    Comment

                    • #11
                      We sure did not put that 704 in your title as we cannot change your info, so you must have.

                      And it looks like you cannot change it either

                      Comment

                      • #12
                        Sorry, I didn't mean to imply that, I am new to this forum and didn't know what the "title" line meant so I left it blank. somewhere I must have used that search and it got picked up. But in my question I didn't say it was a 704. At any rate, does anyone have an answer for adjusting the friction on the unit I do have?

                        Comment

                        • #13
                          I don't know however, under the center cover(on the lever itself), I would THINK, would be a good place to look for an adjustment screw. It shouldn't be a PIA to adjust..


                          If you call the boat manufacturer (or rigger if local), they may be able to tell you.


                          Part #11, shows a Throttle friction part, if that helps..

                          2006 and Later Rigging Yamaha Outboard CONTROL SIDE FLUSH PREMIUM Diagram and Parts
                          Last edited by TownsendsFJR1300; 06-08-2016, 07:09 PM.
                          Scott
                          1997 Angler 204, Center Console powered by a 2006 Yamaha F150TXR

                          Comment

                          • #14
                            That exposed, flat head, screw that you can see on the backside... I take it that's not it? I honestly don't know, but that's where I'd start.

                            Second place would be as Scott mentioned, under the center cover... that off-center screw.

                            Third... those two long screws on the front side of the control box. Although, given that there's two, I would also 'guess' that there for the throttle hand throw.
                            Last edited by DennisG01; 10-24-2014, 10:17 AM.
                            2000 Yamaha OX66 250HP SX250TXRY 61AX103847T
                            1982 Grady Weekender/Offshore (removed stern drive & modded to be an OB)

                            Comment

                            • #15
                              Just FYI, I found it. The screw in the black Bezel that fits against the side wall and looks like its a mounting screw is actually the friction adjustment.
                              Thank You for all your efforts.

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X