Yamaha Outboard Parts
Yamaha   Yamaha Outboard Parts
 
Yamaha Outboard Forum Yamaha Outboard Parts Discussion Forum Yamaha Outboard Parts Boat Parts Yamaha Outboard Forum Outboard Motor Parts Contact Us
Yamaha Parts
  #1 (permalink)  
Old 10-23-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default Converting 15MSH from tiller to remote?

I have a 2010 model 15MSH 2 stroke that I would like to convert from tiller to remote control steering and engine controls. I am not clear on whether I can retain my original tilt tube (clamp bracket bolt) or if I have to buy a different one.

The existing factory tube is 9 1/2" long, 5/8" ID, 7/8" OD, 14 threads per inch. There is only about 1/4" of the tube protruding from each end past the self locking nuts and it doesn't look like that will be enough for the steering cable housing to attach to.

Can any one tell me the part number and correct length of tube that has to be used with remote steering?

Robert
Reply With Quote
  #2 (permalink)  
Old 10-24-2012
Super Moderator
 
Join Date: Dec 2009
Location: Lake Placid, Fl
Posts: 10,383
Default

Would need to change tilt tube, here is parts needed
63V-48501-00-00 Remote conversion kit
63V-61350-00-00 Steering Guide Attachment
63V-43131-10-00 Steering Hook
63V-48511-01-00 Longer Tilt Tube
97075-08035-00 Bolt
92995-08600-00 Washer
95780-08300-00 Nut

and your choice of control box and two control cables.
__________________
Regards
Boats.net
Yamaha Outboard Parts
Reply With Quote
  #3 (permalink)  
Old 10-24-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

Thanks so much for the information.

Next questions.

The engine is pull start only, the helm is starboard side mount, what control box would I need for throttle and gear shift?

I'm assuming that after the remote install, the tiller gets removed. Is there some sort of closure plate available that covers the tiller mounting hole in the housing to make it look like the thing wasn't just hacked?

If the tiller is removed then the stop button is also gone, is a stop button part of the control box?

Last edited by Hocus-Pocus; 10-24-2012 at 10:59 AM.
Reply With Quote
  #4 (permalink)  
Old 10-24-2012
Super Moderator
 
Join Date: Dec 2009
Location: Lake Placid, Fl
Posts: 10,383
Default

Your motor should use a pull to open control, but make sure by looking at where throttle cable will connect to engine and see if controls would have pull throttle linkage to open throttle on carb.
Then order 701-48101-11-00 701 starboard mount control with stop switch and two MAR-CABLE-xx-SC(replace xx with length cables needed) control cables.
Remote conversion kit will include rubber plugs for cowling.
__________________
Regards
Boats.net
Yamaha Outboard Parts

Last edited by boats.net; 11-19-2012 at 11:20 AM.
Reply With Quote
  #5 (permalink)  
Old 10-24-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

Thanks again for your prompt and detailed response. I checked the throttle rotation and it is indeed pull to open.
__________________
Robert
1993 Bayliner 3288, 2012 AB 9.5AL RIB, 2010 Yamaha 15MSH
Reply With Quote
  #6 (permalink)  
Old 10-25-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

Parts,
There seems to be a problem with part # 701-48101-11-00. When I try to order it it comes up as a bad number.
__________________
Robert
1993 Bayliner 3288, 2012 AB 9.5AL RIB, 2010 Yamaha 15MSH
Reply With Quote
  #7 (permalink)  
Old 10-25-2012
Super Moderator
 
Join Date: Dec 2009
Location: Lake Placid, Fl
Posts: 10,383
Default

It is a good number, not sure why shopping cart is not finding it. Call boats.net at 877-408-1499 they can help you order it.
__________________
Regards
Boats.net
Yamaha Outboard Parts
Reply With Quote
  #8 (permalink)  
Old 10-26-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

I called boats.net, they advised me to try the multiple parts search. It comes up OK on that, but not the individual parts search. Odd.

Thanks for your help.
__________________
Robert
1993 Bayliner 3288, 2012 AB 9.5AL RIB, 2010 Yamaha 15MSH
Reply With Quote
  #9 (permalink)  
Old 11-19-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

I've run into a problem with the 701-48101-11-00 install, a couple of problems actually.

First of all, the 63V-48501-00-00 remote conversion kit has the throttle lever attachment positioned below the shaft, clockwise to open, which now makes the throttle a push to open situation. I don't know how I could have determined this without either seeing the conversion kit or having this information before hand.

The second problem is while the helm station is on the starboard side, the control box mount is of such a design and the control box is so large that it won't allow the box to be mounted on the inboard side (right mount) so it now has to be mounted on the outboard side, which would be a left mount.

What would be the correct part number for the 701 control with stop button, left mount, push to open throttle?
__________________
Robert
1993 Bayliner 3288, 2012 AB 9.5AL RIB, 2010 Yamaha 15MSH
Reply With Quote
  #10 (permalink)  
Old 11-19-2012
Super Moderator
 
Join Date: Dec 2009
Location: Lake Placid, Fl
Posts: 10,383
Default

701-48130-02-00 701, port mount, push to open but is not available with stop switch.
__________________
Regards
Boats.net
Yamaha Outboard Parts
Reply With Quote
  #11 (permalink)  
Old 11-19-2012
Junior Member
 
Join Date: Oct 2012
Location: Gibsons, BC, Canada
Posts: 18
Default

Thanks for your prompt response.
__________________
Robert
1993 Bayliner 3288, 2012 AB 9.5AL RIB, 2010 Yamaha 15MSH
Reply With Quote
  #12 (permalink)  
Old 11-15-2013
Junior Member
 
Join Date: Nov 2013
Posts: 1
Default

Quote:
Originally Posted by boats.net View Post
I would like to convert a 2003 Yamaha 15MSHB from Tiller to Wheel.

Can I use the same conversion kit as above?

I gather for the 63V-48501-00-00 Remote Cont. Attachment Assy. would work for the controls.

Also what is the difference between the 2003 15MSHB and the F15MSHB Models?
Reply With Quote
  #13 (permalink)  
Old 12-08-2013
Junior Member
 
Join Date: Dec 2013
Posts: 2
Default 15 HP From Tiller to Wheel

I have a 2002 15 MSHA and need a tiller handle. My original handle is missing. I would be interested in buy your tiller handle.
Reply With Quote
  #14 (permalink)  
Old 03-21-2014
Junior Member
 
Join Date: Mar 2014
Posts: 8
Default

Know this post is old but have a question and the push and pull of a control. I have converted my 1998 25 Yamaha to the remote control. Similar setup with the control on the side now pushing from the back (I guess? could be pull) I was thinking of using a generic SeaChoice SCP28401 control. Looks like and old Morse. It's called out as a throttle/clutch control. When you look up inside it, it has an attachment on both sides of the bell crank. Is this for push or pull? One seller said it was attaching to another control, but the model says single station only.
__________________
RIPSAW
Reply With Quote
  #15 (permalink)  
Old 03-22-2014
Senior Member
 
Join Date: Dec 2010
Location: KDH NC
Posts: 4,934
Default

you really need to start a new thread.
thread hopping gets to confusing.
but to answer your question, most all generic morse type single station single lever boxes can push or pull for both shift and throttle.
simply depends on where you mount the cable.
most are also adjustable for stroke length as well.
most single lever boxes cannot be used as second station cable to cable setups.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -4. The time now is 10:19 PM.

Outboard Parts

Other Forums
Mercury Parts
Suzuki Parts
Evinrude Parts
Johnson Parts
Honda Parts

Copyright 2000 - 2014, Outdoor Network LLC